RV Keyless Entry Door Lock ML100-6001

1. General Specifications
Model : ML100-6001 Electronic Lock
Rated Voltage : DC 6 V
Operating Voltage : DC 3.8–7.2 V
Operating Current: 200 mA (Peak Current ≤ 500 mA)
Standby Current: ≤ 20 µA (Bluetooth Disabled) / ≤ 200 µA (Bluetooth Enabled)
IP Protection Rating: IP65 (Protective Cover Required)
Salt Spray Resistance:
Outside of Door Panel: 96 Hours Neutral Salt Spray Test
Inside of Door Panel: 48 Hours Neutral Salt Spray Test
Coating: 96 Hours Neutral Salt Spray Resistance
Unlocking Methods: Mechanical Key, Fingerprint, Remote Key Fob, Password
Flammability Rating: UL94 V-0
Lock Cylinder Type : Mechanical Lock Cylinder (2,000 Key Combinations)
Drive Mechanism: Electric Motor
Vibration Test:
Frequency: 50 Hz; Amplitude: 5 mm; X, Y and Z Axes; 30 Minutes per Axis; No Abnormalities After Testing (Packaged)
Mechanical Strength:
Outer Flip Cover: Load Capacity 400 N
Inner Flip Cover: Load Capacity 400 N
Service Life / Warranty: 2-Year Warranty from Date of Manufacture or 20,000 Operating Cycles (Excluding Batteries)
Environmental Compliance: RoHS 2.0
Applicable Door Thickness: 35–45 mm
Key Operating Torque: 2.5 N·m
Door Offset Height: N/A
Lock Weight: 1.4 kg

2. Remote Key Fob Specifications
Flammability Rating : UL94 V-0
Remote Control Range: ≤ 15 m
Service Life / Warranty: 2-Year Warranty from Date of Manufacture or 7,000 Operating Cycles

3. Component Specifications
Housing: Aluminum Alloy,Black High Salt-Spray-Resistant Coating;
Front Flip Cover:Zinc Alloy,Black High Salt-Spray-Resistant Coating;
Pressure Plate:Zinc Alloy,Black High Salt-Spray-Resistant Coating;
Locking Bolt:Zinc Alloy,Trivalent Chromate Conversion Coating,Color Zinc,72 h;

4. Communication
Bluetooth Communication:Remote Key Fob Communication

5. Environmental Conditions
Operating Temperature: −40°C to +70°C
Operating Humidity:≤ 80% RH
Storage Temperature:−40°C to +70°C
Storage Humidity:≤ 90% RH
Operating Altitude:−60 m to 4,000 m

4.1 Mechanical Key Unlocking

Insert the mechanical key into the “DEADBOLT” keyhole and turn it 90° clockwise.
Turn the key 90° counterclockwise and remove it. Then insert the same key into the “HANDLE” keyhole and turn it 90° clockwise.

Note: The mechanical key can be inserted into either keyhole first. There is no required sequence.

4.2 Mechanical Key Locking

Insert the mechanical key into the “DEADBOLT” keyhole and turn it 90° counterclockwise.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° counterclockwise.

Note: To remove the key from the “DEADBOLT” keyhole, it must be turned an additional 90° counterclockwise.

The “HANDLE” keyhole can remain in either the locked or unlocked position as required. This does not affect the actual locking of the lock, provided that the “DEADBOLT” is securely locked.

4.3 Password Unlocking

Ensure that the lock is in the locked position.
Enter the password (default password: 1234) and press the “UNLOCK” button within 3 seconds. If more than 3 seconds have elapsed, the password must be entered again. The motor retracts the latch into the lock body, and the buzzer emits three beeps.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° clockwise.

4.4 Password Locking

Ensure that the lock is in the unlocked position.
There are two locking methods:

- Method 1: Press and hold the “LOCK” button for 3 seconds. The latch bolt will extend.

- Method 2: Enter the password and press the “LOCK” button to lock.

After successful locking, the buzzer emits two beeps.
Insert the mechanical key into the “HANDLE” keyhole, turn it 90° counterclockwise, and remove the key to lock the external handle.

4.5 Changing the Password

First, make sure you know the current password (or the default password).
Press and hold the “8” and “LOCK” buttons simultaneously, then release both buttons. Within 5 seconds after the buzzer sounds, enter the old/default password (1234) and press the “LOCK” button.
Enter the new password and press “LOCK”. Enter the new password again and press “LOCK” to confirm.
When the new password has been successfully set, the buzzer emits three long beeps and the keypad backlight turns off.

Example: Changing the default password from 1234 to 5678

The default password is 1234.
Press and hold “8” and “LOCK” simultaneously, then release both buttons. Enter “1234” and press “LOCK”.
Enter “5678” and press “LOCK”. Enter “5678” again and press “LOCK”.
Unlock using the new password: enter “5678” and press “UNLOCK” to initiate unlocking.

4.6 Remote Key Fob Pairing

On the back of the lock, move the remote control switch to the “ON” position. Press any button on the front keypad to wake up the lock. Once the keypad backlight turns off, the remote key fob function is enabled.
Lock side: Press and hold the “FOB Learn” button for 3 seconds. The lock buzzer emits one long beep, and the keypad backlight starts flashing, indicating that the lock has entered pairing mode.

Remote key fob side: Once the lock is in pairing mode, press and hold either button on the remote key fob. The red indicator on the remote key fob remains illuminated, indicating that pairing has started.

   When the lock buzzer emits one long beep and the keypad backlight turns off, pairing is complete. The remote key fob can now be used to lock and unlock the device.

Notes:

- To pair another remote key fob, repeat Steps 1–2.

- To disable the remote key fob function, move the switch to the “OFF” position.

- One lock can be paired with up to three remote key fobs.

4.7 Remote Key Fob Unlocking

Move the remote control switch on the lock to the “ON” position.
Press the unlock button on the remote key fob. The red indicator on the remote key fob flashes slowly. When the lock receives the unlocking signal, the keypad backlight flashes and the buzzer emits three beeps. The motor retracts the latch into the lock body, allowing the external handle to be released and pulled.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° clockwise.

4.8 Remote Key Fob Locking

Move the remote control switch on the lock to the “ON” position.
Press the “LOCK” button on the paired remote key fob. The red indicator on the remote key fob flashes slowly. When the lock receives the signal, the keypad backlight flashes and the buzzer emits two beeps. The motor extends the latch bolt.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° counterclockwise.

4.9 Fingerprint Unlocking

Ensure that the lock is in the locked position.
Place a registered finger on the fingerprint sensor. The green indicator on the fingerprint module remains illuminated, and the buzzer emits one long beep.
Press the “UNLOCK” button to confirm unlocking.
The latch bolt retracts into the lock body, and the buzzer emits three beeps.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° clockwise.

4.10 Fingerprint Locking

Ensure that the lock is in the unlocked position.
Place a registered finger on the fingerprint sensor. The green indicator on the fingerprint module remains illuminated, and the buzzer emits one long beep.
Press the “LOCK” button to confirm locking.
The latch bolt extends, and the buzzer emits two beeps.
Insert the mechanical key into the “HANDLE” keyhole and turn it 90° counterclockwise.

4.11 Fingerprint Registration

Press and hold the “0” and “LOCK” buttons simultaneously, then release both buttons. The buzzer emits two long beeps, and the keypad flashes for 2 seconds.
Enter the cabinet lock password and press the “LOCK” button. The buzzer emits one short beep, and the blue indicator on the fingerprint module illuminates, indicating that the lock has entered fingerprint registration mode.
Place a finger on the fingerprint sensor. When registration is successful, the green indicator illuminates and the buzzer emits one long beep. Then lift your finger.

Recreational Vehicle (RV) Entry Doors
Motorhome Entrance Doors
Caravan and Travel Trailer Entry Doors
Camper Conversion Entry Doors (subject to installation compatibility)

Packaging Specifications

Each lock is individually packaged with an EPE foam insert and an inner box.

Each package includes one pen-type screwdriver, four alkaline zinc-manganese batteries, one user manual, and one YS915 electronic key.

Precautions

1. Do not operate the product beyond the limits specified in this specification.

2. If any changes to the specifications in this document are required, please submit the relevant requirements in advance.

3. In the event of any discrepancies between this document and other technical documents or information, this document shall take precedence.

4. Do not use the product in environments containing flammable gases or other hazardous conditions.

5.Operators must wear protective gloves during transportation and installation to prevent injuries caused by falling objects or other hazards.

6. Do not strike or impact the lock during installation, as this may damage its components. Do not clean or wipe the lock with chemical reagents, as they may damage the surface coating.
7.Ensure that the door panel remains level during installation. The mounting cutout in the cabinet door must match the required dimensions of the lock body.
8. After installation, connect the wiring harness. Do not wrap the connecting cable around the lock or pull it forcefully, as this may damage the lock connector and cause the lock to malfunction.